13.12.2011, 21:59
|
#1 |
| Arcorneuling
Registriert seit: 24.11.2011 Beiträge: 4
|  602 Bootmenu + Bootlog über serielle Schnittstelle
Für interessierte Zeitgenossen, hier das Bootmenu und komplette Bootlog eines Vodafone 602, erstellt über die serielle Schnittstelle auf der Platine: Zitat:
================================================== =====================
Wireless ADSL Gateway DANUBE Loader V1.01.01 build Oct 2 2008 10:46:12
Arcadyan Technology Corporation
================================================== =====================
EON EN29LV640B bottom boot 16-bit mode found
Copying boot params.....DONE
Press Space Bar 3 times to enter command mode ...123
Yes, Enter command mode ...
[DANUBE Boot]:
======================
[#] Set Serial Number
[2] Use Normal Firmware
[3] Use ART-Testing Firmware
[9] Taggle ART Firmware Enable/Disable
[A] Set MAC Address
[E] Erase Flash
[G] Run Runtime Code
[H] Set Options
[P] Print Boot Params
[u] Upload to Flash
[V] Set Board Version
======================
[DANUBE Boot]:u
UPLOAD Flash
---------------------------------------
Area Address Length
---------------------------------------
[0] Boot 0xB0000000 128K
[1] Configuration 0xB0020000 256K
[2] None 0xB0060000 64K
[3] Special Area 0xB0070000 64K
[4] Primary Setting 0xB0080000 64K
[5] Code Image 0 0xB0090000 3776K
[6] Code Image 1 0xB0440000 3776K
[7] Boot Params 0xB07F0000 64K
[8] Flash Image 0xB0000000 8192K
---------------------------------------
Enter area to UPLOAD:
ERROR: Not a valid area.
[DANUBE Boot]:!
Enter Administrator Mode !
======================
[#] Set Serial Number
[2] Use Normal Firmware
[3] Use ART-Testing Firmware
[9] Taggle ART Firmware Enable/Disable
[A] Set MAC Address
[E] Erase Flash
[G] Run Runtime Code
[H] Set Options
[M] Upload to Memory
[P] Print Boot Params
[R] Read from Memory
[T] Memory Test
[u] Upload to Flash
[V] Set Board Version
[W] Write to Memory
[Y] Go to Memory
[Z] Dump DDR Ram Register
[0] Primary = Image 0
[1] Primary = Image 1
======================
[DANUBE Boot]:g
[0] Passed.
Image[1] at 0xb0090000, len:1624194, type:0
Image[2] at 0xb021cc00, len:766294, type:10
Image[3] at 0xb02d8000, len:238535, type:11
Image[4] at 0xb0312400, len:226496, type:12
Image[5] at 0xb0349c00, len:150508, type:60
Image[6] at 0xb036ec00, len:452105, type:90
Firmware image at 0, ART image at -1
Run-up Normal Firmware...
Unzipping firmware [0(5)] at 0x80002000 ... [ZIP 3] [ZIP 1] done
Run-time code running ...
In c_entry() function ...
install_exception
Co config = 80008483
[INIT] Interrupt ...
##### _ftext = 0x80002000
##### _fdata = 0x80622420
##### __bss_start = 0x8070812C
##### end = 0x8286418C
allocate_memory_after_end> len 941324, ptr 0x8286c190
##### Backup Data from 0x80622420 to 0x8286C18C~0x82951E98 len 941324
##### Backup Data completed
##### Backup Data verified
[GPIO FLOW] SetGpio() Begin ..
gptu: totally 6 16-bit timers/counters
Init timer = 0
************************ LED all ON
************************ LED all OFF
[GPIO FLOW] SetGpio() End.
[INIT] System Log Pool startup ...
[INIT] MTinitialize ..
[INIT] usrclk
CPU Clock 333333334 Hz
mips_counter_frequency:166666667
r4k_offset: 00028b0a(166666)
init_US_counter : time1 = 260435 , time2 = 40260467, diff 40000032
US_counter = 48
cnt1 40987779 cnt2 40989997, diff 2218
Runtime code version: 20.02.024
System startup...
[INIT] Memory COLOR 0, 3000000 bytes ..
[INIT] Memory COLOR 1, 262144 bytes ..
[INIT] Memory COLOR 2, 3516576 bytes ..
EON EN29LV640B bottom boot 16-bit mode found
Set flash memory layout to Boot Parameters found !!!
Bootcode version: V1.01.01
Serial number: R9060XXXXXX
Hardware version: 01
[BUILD-WPA]: Key:B55XXXXXX
[BUILD:PIN] PIN:R9060XXXXXX, MAC:0023XXXXXXXX
[BUILD-PIN]: PIN:64XXXXXX, len=8
EON EN29LV640B bottom boot 16-bit mode found
EON EN29LV640B bottom boot 16-bit mode found
...
(Rest siehe Anhang)
| |
| |
Ähnliche Themen 